Thread: Causes and Solutions to PIP problems

i would not use ibuprofin, only on extreme cases like using primo ace lolol :P
but hot bath is good enough (at least for me), and inject on glutes

i usually like to warm my products before to inject them and the difference with sides on the point of injection is very wide.
Especially with TEST, i dunno why... (250mg/ml)

1cc of Lean Gain in each bicep was the worst. Biceps were also virgins at the time hahahah. 2nd time around, almost no pip

Heating thick oil with a hair dryer before injection helps reduce its viscosity [ Bayer Schering Test-e comes to mind].

Cut your shots 50:50 with sterile filtered oil. If you want to use 50mg of Testosterone Propionate, and you have 100mg/mL Testosterone Propionate- pull 0.5mL of your test prop, and 0.5mL of sterile filtered oil to shoot 1mL of 50mg/mL Testosterone Propionate. This is the #1 best way.
Dont bother with b-12, its water based- absorbed so quickly it will have little to no impact.

I didnt know we could do this... Does the raw get suspended properly if we cut it with oil before injection...?

With the pain test-prop gives, heck Id rather shoot 2 ml than deal with the pain that 1 ml shells out.

I try to get deep in the muscle and sometimes I do run it under some warm water to increase it's viscosity some. I have some test that i crippling and i use to keep EQ on hand to cut it or something cause it was unbearable last time. My whole ass cheek was red and hot. I sucked big time. Never tried bayer schering Test E but heard it is top notch and their Primo as well.

Originally Posted by Kalika ke Akua

I try to get deep in the muscle and sometimes I do run it under some warm water to increase it's viscosity some. I have some test that i crippling and i use to keep EQ on hand to cut it or something cause it was unbearable last time. My whole ass cheek was red and hot. I sucked big time. Never tried bayer schering Test E but heard it is top notch and their Primo as well.

That sounds like badly made test to be honest. I had some thick ugl stuff a while back that seemed to take ages to absorb and sometimes gave irritation. Suspect quality ... Plus it was under dosed too

Originally Posted by Nitrox

Cut your shots 50:50 with sterile filtered oil. If you want to use 50mg of Testosterone Propionate, and you have 100mg/mL Testosterone Propionate- pull 0.5mL of your test prop, and 0.5mL of sterile filtered oil to shoot 1mL of 50mg/mL Testosterone Propionate. This is the #1 best way.
Dont bother with b-12, its water based- absorbed so quickly it will have little to no impact.

I didnt know we could do this... Does the raw get suspended properly if we cut it with oil before injection...?

With the pain test-prop gives, heck Id rather shoot 2 ml than deal with the pain that 1 ml shells out.

The raw isn't "suspended" but is held in solution. A suspension is non dissolved particles that are visible and flowing freely in a liquid medium (think of a snow globe). A solution is solute (hormone powder) dissolved in a liquid which isn't visible to naked eye as the molecules of the solute fit between the molecules of the solvent (hormone dissolved in oil/bb/eo etc).
When it comes to a suspension, the powder inside isn't always homogeneous and can clump or just be floating more in a certain space of the liquid causing uneven distribution. When in a solution, such as our oil preparations, the distribution is homogeneous so there is equal parts of hormone in every bit of the oil. This means that the addition of sterile oil or any oil that isn't completely saturated (the oil can hold additional hormone, some use vet grade eq to dilute which is dosed 50mg/ml which is far from being at saturation point), the hormone(s) become equally distributed throughout the new solution. Thus for the example of 100mg/ml prop, the addition of sterile oil creates a new solution of 50mg/ml. If using another oil with hormones in it such as the vet grade eq, it would yield 50mg prop and 25mg eq per ml. Hope this helps explain the process a bit more.