Mixing oils in one jab

12 posts · started by Didmo1983 · Jul 11, 2015

👤
Didmo1983
Senior Member
Posts: 156
Joined: Jan 2015
Rep: 10
👤
Didmo1983
156 posts · joined Jan 2015
#1
Hi Guys,

I read before it's perfectly fine to mix MTS oils into one jab? I wanted to do 0.5ml x 4 in one jab (Test prop, shredded, lean extreme, supertren). Before I load up the whole cycle I just wanted to check this is fine?

Just wanted to avoid doing the multiple jabs I was doing last cycle.
👤
botchla
Member
Posts: 42
Joined: Jan 2015
Rep: 10
👤
botchla
42 posts · joined Jan 2015
#2
Course man, load it all into one syringe and jab away!
👤
Didmo1983
Senior Member
Posts: 156
Joined: Jan 2015
Rep: 10
👤
Didmo1983
156 posts · joined Jan 2015
#3
botchla wrote:Course man, load it all into one syringe and jab away!


Great. Saves a lot of pinning!
BIGDADDY
MTS STAFF - formally MR BIG
Posts: 2,507
Joined: Jan 2015
Rep: 37
BIGDADDY
2,507 posts · joined Jan 2015
#4
What will save a lot of pinning is taking blends. Seriously.
MTS Support https://support.med-tech.pro
👤
Powertard
Senior Member
Posts: 954
Joined: Jan 2015
Rep: 12
👤
Powertard
954 posts · joined Jan 2015
#5
This ought to be okay when using all MTS products

If you use lab x y z together than you can end up with it all clumping together because some carrier oils react with other carrier oils
👤
Serotonin101
Senior Member
Posts: 236
Joined: Feb 2015
Rep: 10
👤
Serotonin101
236 posts · joined Feb 2015
#6
You'll die bro...

Im kidding. Twice a week I pin 5cc which contains 3 different brands of gear. Different carriers too.
👤
Powertard
Senior Member
Posts: 954
Joined: Jan 2015
Rep: 12
👤
Powertard
954 posts · joined Jan 2015
#7
lol Serotonin ahaha
5ml, damn that is a lot of oil

What are you on?
👤
Didmo1983
Senior Member
Posts: 156
Joined: Jan 2015
Rep: 10
👤
Didmo1983
156 posts · joined Jan 2015
#8
MR BIG wrote:What will save a lot of pinning is taking blends. Seriously.


Eh? I am using shredded, lean extreme and supertren? Aren't these blends?
👤
Serotonin101
Senior Member
Posts: 236
Joined: Feb 2015
Rep: 10
👤
Serotonin101
236 posts · joined Feb 2015
#9
Powertard wrote:lol Serotonin ahaha
5ml, damn that is a lot of oil

What are you on?


Synthol for glute growth! Kidding!
2.5cc desoxytest cyp
1cc mast e
1cc tren e
0.5cc Masteron tren blend.

It's really not so bad. I do legs the next day and the only noticeable issue is a bump in my glute from the Depot for a few days. No soreness or anything.
👤
Liftcore
Junior Member
Posts: 26
Joined: Feb 2015
Rep: 10
👤
Liftcore
26 posts · joined Feb 2015
#10
Last blast i was mixing around 4mL per pin (2mL NPP 2mL Primo) and I had no problems. I'll find any excuse to pin less lmao go for it OP
👤
ross123
Junior Member
Posts: 5
Joined: Jan 2015
Rep: 10
👤
ross123
5 posts · joined Jan 2015
#11
mixing is fine. less jabbing and more compounds working together. the only drawback for me is I like to know what works best for me so mixing compounds might not be the best solution until uve found this out

eg u could mix test enth with tren say.... the tren may be working well where the enth may not yet because uve made gains u would think they work well together whereas u could run cyp and tren and possibly get better gains. all depends on the individual as to what compounds work best. in my opinion find out what works best for u individually and then go from there. May take a while but long term u will be saving time and not wasting money
👤
patd8686
Junior Member
Posts: 9
Joined: Feb 2015
Rep: 10
👤
patd8686
9 posts · joined Feb 2015
#12
I mix oils and winni inject in same needle when I run winni inject. Oil and water separates but its not a problem. As long as it all gets into the muscle. .
Reply

📦 Move Thread

✂️ Split Thread Here

This post and all following posts will become a new thread.